How radon mitigation systems work
Last updated
Sub-slab depressurization and other radon reduction methods explained, what installation involves, and how to check a system is working.
If your home tests at or above 4 pCi/L, EPA recommends fixing it. Here is the good news, in EPA's words: radon reduction systems work, some can cut radon levels by up to 99 percent, and most homes can be fixed for about the same cost as other common home repairs.
The main method: sub-slab depressurization
Most systems in homes with basements or slab foundations rely on active soil depressurization, often called sub-slab depressurization. A contractor:
- drills a hole through the floor slab and digs out a small pit of fill underneath,
- seals a plastic pipe into the hole,
- runs the pipe to a quiet in-line fan, usually in an attic, garage, or outside the house,
- vents the exhaust above the roof line.
The fan creates a gentle vacuum under the slab, so soil gas gets pulled into the pipe and sent outdoors instead of seeping into the house. EPA explains that the discharge has to go above the roof, away from windows and other openings, so the concentrated radon spreads out and doesn't come back into the home.
Other foundation types
- Crawl spaces. A heavy plastic sheet (vapor barrier) is laid over the soil and sealed, and a pipe and fan pull air from beneath it. This is called sub-membrane depressurization.
- Block walls. Hollow concrete block foundation walls may need their cavities depressurized as well.
- Sump pits. An existing sump can act as the suction point if it's sealed with an airtight lid.
Supporting steps
Sealing cracks and openings in the foundation helps a system work better and saves energy, but EPA's guidance is that sealing alone has not been shown to lower radon reliably. Ventilation approaches, such as heat recovery ventilators, can help in some homes.
Choosing a contractor
EPA recommends hiring a qualified mitigation contractor. It notes that states receiving federal indoor radon grants keep lists of providers credentialed through a state license or a national proficiency program (NRPP or NRSB). Get more than one estimate. Ask how the contractor will test the soil's suction (“communication”) under the slab, where the pipe and fan will go, and whether a post-mitigation test is included. Your state radon program, linked on our state pages, can help.
Cost
EPA doesn't publish a national price. It says costs vary with the size and design of the home and the methods needed, and that most homes can be fixed for about the same cost as other common home repairs. The fan also draws some electricity around the clock, and it will need replacing at some point.
Checking that it works
EPA's guidance for owners:
- Look at the warning device regularly. EPA says radon reduction systems need occasional maintenance and that you should check the system's warning device on a regular basis. Many systems use a U-tube manometer on the pipe; uneven liquid levels show the fan is pulling a vacuum, and levels that even out suggest the fan has stopped.
- Expect to replace the fan eventually. EPA notes fans may last five years or more (warranties tend not to go past five years) and then need repair or replacement.
- Retest. Test after installation to confirm the system worked, and retest from time to time and after major renovations, as EPA's testing guidance suggests.
If you are building new
Radon-resistant features cost less to put in during construction. See radon-resistant new construction.
Why the pipe goes above the roof
EPA explains that radon has to be vented into the air above the roof. Concentrations at the discharge can be extremely high, but they fall off sharply with distance and approach background levels within 3 to 4 feet of the discharge point. EPA disallowed ground-level discharge because the gas could be pulled back into the house, and because children might be exposed near the outlet. When you look over a contractor's proposal, check where the discharge will be and confirm that it meets the national standard and any state rules.
How well do systems work?
Results depend on the foundation, the soil under the slab, how well the slab is sealed, and the design of the fan and pipe. A good contractor runs a quick diagnostic, such as a pressure field extension test that drills small holes in the slab to measure how far suction reaches, to plan where the suction points go.
Installation day: what to expect
- Assessment. The contractor looks over the foundation, sump, and crawl spaces, and settles on suction point locations and the pipe route.
- Suction point. A hole is cored through the slab and a small pit is dug out underneath to help air flow.
- Piping. PVC pipe runs from the suction point to the fan, either up through the house to the attic or along the outside.
- Fan. The fan is mounted in the attic, the garage, or outdoors, never in the living space or a basement, so a leak on the pressurized side can't push radon indoors.
- Sealing. Cracks and openings the crew can reach, along with the sump lid, are sealed.
- Monitor. A U-tube manometer or electronic alarm is installed and marked with the starting reading.
- Labeling. The system gets a label with the installer's contact details.
Most single-family installations are finished in a day or less.
After installation: confirm it works
EPA guidance calls for a post-mitigation test, usually a short-term test run at least 24 hours after the system starts, and within 30 days of installation. Follow-up testing then continues from time to time. EPA's retest guidance suggests testing again after renovations or changes in how you use the home. EPA's Consumer's Guide to Radon Reduction says it is a good idea to retest at least every two years to be sure radon levels remain low.
Operating costs
The fan runs nonstop. Radon fans vary widely in power draw depending on the model, so the yearly electricity cost depends on fan size and local rates. Heating and cooling costs can go up slightly, because the system pulls a small amount of conditioned air out of the house. Sealing helps cut this down.
Warranties and contracts
Ask for a written proposal that covers:
- the system design and fan model;
- the post-mitigation result the contractor commits to, often below 4 pCi/L, sometimes lower;
- what happens if that target isn't met;
- the warranty on workmanship and the fan;
- who is responsible for permits;
- the contractor's credentials, such as a state license and national certification.
See hiring a radon mitigation contractor for a complete checklist.
Free checklist · PDF
Radon Test Checklist
A one-page, step-by-step checklist for running a home radon test right the first time, and what to do with the number.
- Short-term vs. long-term test: which to use
- Closed-house conditions and where to place the kit
- What 2, 4 and 8 pCi/L mean and when to fix
Free. We email you the download link, plus an occasional plain-English guide. Unsubscribe any time. We never sell your email. Privacy
Sources
- U.S. EPA, How much can a radon mitigation system cost?
- U.S. EPA, How do I know if my radon mitigation system is working properly?
- U.S. EPA, Why must radon be vented into the air above my home’s roof?
- U.S. EPA, A Consumer’s Guide to Radon Reduction, via EPA radon publications
- U.S. EPA, How often should I test/retest my home for radon?
- U.S. EPA, Consumer's Guide to Radon Reduction (2016)